| 1 |
IS 516(Part 1/Section 1):2021 - Hardened Concrete-Methods of Tests-( Part 1-Testing of strength of Hardened Concrete-Determination of Compressive, Flexural strength and Split tensile strength) |
Hardened Concrete-Methods of Tests-( Part 1-Testing of strength of Hardened Concrete-Determination of Compressive, Flexural strength and Split tensile strength) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3 (Compressive strength of concrete cubes(MPa)) |
1200.0 |
|
|
| 2 |
IS 516 (Part 1/Sec 1) : 2021 (3 set CC cubes) - Hardened Concrete —Methods of Test
(Part 1 Testing of Strength of Hardened Concrete)
(Section 1 Compressive, Flexural and Split Tensile Strength) |
Hardened Concrete —Methods of Test
(Part 1 Testing of Strength of Hardened Concrete)
(Section 1 Compressive, Flexural and Split Tensile Strength) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3 (Compressive strength,MPa) |
3600.0 |
|
|
| 3 |
NTH/NER/Custom - Effluent Water |
Effluent Water |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1. (pH value) |
500.0 |
|
| 2. (Oil & Grease, mg/l) |
1000.0 |
|
| 3. (BOD (3 days at 27 Deg C), mg/l) |
3000.0 |
|
| 4. (COD, mg/l) |
2000.0 |
|
| 5. (Suspended solids, mg/l) |
500.0 |
|
| 6. (Phenols, mg/l) |
1000.0 |
|
| 7. (Sulphides (as H2S), mg/l) |
1000.0 |
|
| 8. (Cyanide (as CN), mg/l) |
1000.0 |
|
| 9. (Ammonia (as total ammonia - N), mg/l) |
1000.0 |
|
| 10. (Total khjeldal nitrogen, mg/l) |
1000.0 |
|
| 11. (Phosphorous (as PO4), mg/l) |
500.0 |
|
| 12. (Chromium (Hexavalent), mg/l) |
500.0 |
|
| 13. (Total chromium (as Cr), mg/l) |
500.0 |
|
| 14. (Lead (as Pb), mg/l) |
1000.0 |
|
| 15. (Mercury (as Hg), mg/l) |
1000.0 |
|
| 16. (Zinc (as Zn), mg/l) |
500.0 |
|
| 17. (Nickel (as Ni), mg/l) |
500.0 |
|
| 18. (Copper (as Cu), mg/l) |
500.0 |
|
| 19. (Vanadium (as V), mg/l) |
1000.0 |
|
| 20. (Silica (as SiO2), mg/l) |
1000.0 |
|
| 21. (Aluminium (as Al), mg/l) |
1000.0 |
|
|
| 4 |
398 (Part-4) (1994) - ALUMINIUM CONDUCTORS FOR OVERHEAD TRANSMISSION PURPOSES,
PART 4 ALUMINIUM ALLOY STRANDED CONDUCTORS (ALUMINIUM-MAGNESIUM-SILICON TYPE) |
ALUMINIUM CONDUCTORS FOR OVERHEAD TRANSMISSION PURPOSES,
PART 4 ALUMINIUM ALLOY STRANDED CONDUCTORS (ALUMINIUM-MAGNESIUM-SILICON TYPE) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 3.1.4 (Lay Ratio) |
1000.0 |
|
| 7.1 (Wire Diameter) |
1000.0 |
|
| 12.2.1 (Breaking Load Test of Strand) |
3000.0 |
|
| 12.3 (Elongation Test) |
3000.0 |
|
| 12.4 (Resistance Test) |
2000.0 |
|
|
| 5 |
14255 (1995) - Aerial Bunched Cables for working
voltages up to and including 1100 Volts-Reaffirmed 2020 specification |
Aerial Bunched Cables for working
voltages up to and including 1100 Volts-Reaffirmed 2020 specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 10.1 sl no 1(b)(i) ,10.2 sl no(c) (Test on messenger conductor Breaking load) |
1000.0 |
|
| 10.1 sl no 1(b)(ii), 10.2 (d) (Test on messenger conductor Elongation test) |
1500.0 |
|
| 10.2 (e) (Conductor resistance test) |
2000.0 |
|
| 10.1 sl no 1(e),10.2(f) (Test for thickness of insulation) |
1500.0 |
|
| 10.1 sl no 1(g),10.2(k) (High Voltage test) |
1500.0 |
|
| 10.1 sl no 1(c)(i),10.2 (g) (Physical test for XLPE insulation Tensile strength and elongation at break) |
1500.0 |
|
| 10.1 sl no 1(c)(iii),10.2(h) (Physical test for XLPE insulation Hot set test) |
2000.0 |
|
| 10.1 sl no 1(f),10.2(j) (Insulation resistance (Volume Resistivity) test) |
1500.0 |
|
|
| 6 |
IS 9845 (1998) - Determination of overall migration of constituents of plastics materials and articles intended to come in contact with foodstuffs - Method of analysis (Second Revision) |
Determination of overall migration of constituents of plastics materials and articles intended to come in contact with foodstuffs - Method of analysis (Second Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 1 (Overall migration in simulant A) |
3000.0 |
|
| 1 (Overall migration in simulant 'B') |
3000.0 |
|
| 1 (Overall migration in simulant 'C1') |
3000.0 |
|
| 1 (Overall migration in simulant 'C2') |
3000.0 |
|
| 1 (Overall migration in simulant 'D') |
3000.0 |
|
| 1 (Overall migration in simulant 'E') |
3000.0 |
|
|
| 7 |
IS 516 (Part-11) (2020) - Hardened Concrete - Determination of Portland cement Content of Hardened Hydraulic Cement Concrete |
Hardened Concrete - Determination of Portland cement Content of Hardened Hydraulic Cement Concrete |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Clause no.6 (Ratio of Cement : Concrete) |
6000.0 |
|
|
| 8 |
IS 8183 (1993) - Bonded mineral wool - Specification (First Revision) |
Bonded mineral wool - Specification (First Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.1,4.2 (Bulk density) |
1000.0 |
|
|
| 9 |
IS 9537:Part 3 (1983) - Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating materials |
Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating materials |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 12 (12.1.2 Of IS:9537-Part I Insulation Resistance) |
2000.0 |
|
| 12.1 (12.1.1 of IS:9537-Part I Electrical Strength) |
2000.0 |
|
| 6.1 (Marking, manufacturer's name/trade mark, Visual verification (Naked Eye)) |
- |
|
| 6.4 (Durability of Marking) |
- |
|
| 7.4 (Uniformity of Wall Thickness) |
- |
|
| 8 (Construction) |
1000.0 |
|
|
| 10 |
IS 398 : Part 2 (1996) - Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision) |
Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 12 (Seal, Packing & Markings (7/30/54 wire construction)) |
- |
|
| 10 (Construction (7/30/54 wire construction)) |
- |
|
| 13.2 (Measurement of diameter of individual Aluminium wires (7 wire construction)) |
1000.0 |
|
| 13.2(1) (Diameter of individual steel wires (7 wire construction)) |
1000.0 |
|
| 13.6 (Resistance of Aluminium wire (7 wire construction)) |
5000.0 |
|
| 13.8 (Measurement of lay ratio(7 wire construction)) |
2000.0 |
|
| 13.5 (Wrapping test on Aluminium and Steel wires (7 wire construction)) |
1000.0 |
|
| 13.6 (Resistance Test as per Clause 13.6 (Table 1) in Ohms/km) |
3000.0 |
|
| 13.7(1) (Galvanizing test-Mass of zinc coating(7wire construction)) |
2000.0 |
|
| 13.3(1) (Breaking load of individual steel wires(30 or 54 wire construction)) |
1500.0 |
|
| 13.3.1 (Approximate calculated breaking load (7 wire construction)) |
- |
|
| 13.4.2 (Ductility test-Elongation test on steel wires (7 Wire construction)) |
3500.0 |
|
| 13.3 (Breaking load of individual Aluminium wires (7 wire construction)) |
3500.0 |
|
|
| 11 |
IS 9537 (Part 1 & 3) - SPECIFICATION FOR CONDUITS FOR ELECTRICAL INSTALLATIONS |
SPECIFICATION FOR CONDUITS FOR ELECTRICAL INSTALLATIONS |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6 (Marking) |
1000.0 |
|
| 7.4 (Uniformity of Wall Thickness) |
1000.0 |
|
| 8 (Construction) |
1000.0 |
|
| 12 (Electrical Strength) |
4000.0 |
|
| 12 (Insulation Resistance) |
4000.0 |
|
|
| 12 |
Custom - Custom specification for Rigid polyurethane Foam |
Custom specification for Rigid polyurethane Foam |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Vide Annexure) |
1000.0 |
|
|
| 13 |
IS 1489(Part 1):2015 - PORTLAND POZZOLANA CEMENT-SPECIFICATION |
PORTLAND POZZOLANA CEMENT-SPECIFICATION |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| Table1,6.i.a (Insoluble residue, percent by mass-maximum) |
500.0 |
|
| Table1,6.ii (Magnesia, percent by mass) |
500.0 |
|
| Table1,6.iii (Total Sulphur content as sulphuric anhydride (SO3), percent by mass) |
500.0 |
|
| Table1,6.iv (Loss on ignition, percent by mass) |
500.0 |
|
| Table1,6.v (Chloride content, percent by mass) |
500.0 |
|
| Table1,6.vi (Alkali content (%)) |
1000.0 |
|
| Table 2, 7, i (Fineness, sq m/kg) |
1000.0 |
|
| Table 2, 7, iv,a (Compressive strength-MPa, 72±1 h) |
1000.0 |
|
| Table 2, 7, iv,b (Compressive strength-MPa, 168±2 h) |
1000.0 |
|
| Table 2, 7, iv,c (Compressive strength-MPa, 672±4 h) |
1000.0 |
|
| Table 2, 7, iii a (Setting time-Initial, minutes) |
250.0 |
|
| Table 2, 7, iii,b (Setting time-final, minutes) |
250.0 |
|
| Table 2 ,7.ii.a (Soundness-Lechatelier method,mm) |
500.0 |
|
| Table 2 ,7.ii.b (Soundness-autoclave method, percent) |
1000.0 |
|
| Table 2, 7, vi (Drying shrinkage,percent) |
1000.0 |
|
| custom (Consistency (%)) |
500.0 |
|
|
| 14 |
Custom IS 4658 (2019) - Specification for Coated Paper & Art board |
Specification for Coated Paper & Art board |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (vide Annexure) |
12000.0 |
|
|
| 15 |
Custom - Specification for Nitrile Rubber |
Specification for Nitrile Rubber |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Vide Annexure) |
2000.0 |
|
|
| 16 |
IS 15622 Reaffirmed (2017) - Pressed ceramic tiles [All Tests IS 13630] |
Pressed ceramic tiles |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6, Table 5 (Dimensions-Length) |
1000.0 |
|
| 6, Table 5 (Dimensions-Breadth) |
1000.0 |
|
| 6, Table 5 (Dimensions-Thickness) |
1000.0 |
|
| 4.2 (Water Absorption, %) |
1000.0 |
|
| 6, Table 5 (Modulus of Rupture) |
2000.0 |
|
| 6, Table 5 (Modulus of Rupture without Breaking strength) |
3000.0 |
|
| 6, Table 5 (Breaking Strength) |
2000.0 |
|
| 6, Table 5 (Breaking Strength without MoR) |
3000.0 |
|
| 4.2 (Crazing) |
1500.0 |
|
| 6, Table 5 (Scratch Hardness) |
2000.0 |
|
| 6, Table 5 to 9, Sl.(iii),(a,b,c) (Chemical properties - Glazed Tiles - IS 13630 (8):2019) |
3000.0 |
|
| 6, Table 9, Sl.(iii),(a,b,c) (Chemical properties - unglazed Tiles - IS 13630 (7):2019) |
3000.0 |
|
| 6, Table 8 & 9 (Bulk Density) |
1000.0 |
|
|
| 17 |
IS 2250:1981 - Code of Practice for Preparation and use of Masonry Mortars |
Code of Practice for Preparation and use of Masonry Mortars |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6,Table 1 (Grade of Mortar-Mortar mix ratio (IS 1199)) |
5000.0 |
|
|
| 18 |
IS 2250/On the lines of ASTM/IS 1727/2770 - MICRO CONCRETE |
MICRO CONCRETE |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 19 |
Custom - Specification for Paper |
Specification for Paper |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| - (Vide Annexure) |
12000.0 |
|
|
| 20 |
IS 15778 (2007) - Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification |
Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 9.1 (Visual Appearance) |
1000.0 |
|
| 7.1.3 (Length) |
1000.0 |
|
| 7.1.2 (Wall Thickness) |
1000.0 |
|
| 7.1.1 (Diameter at any point ) |
1000.0 |
|
| 7.1 (Diameter) |
1000.0 |
|
| 9.6 (Density) |
1000.0 |
|
| 9.5 (Vicat Softening Temperature) |
1500.0 |
|
|
| 21 |
IS:15778:2007 - CHLORINATED POLYVINYL CHLORIDE (CPVC) PIPES FOR POTABLE HOT AND COLD WATER DISTRIBUTION SUPPLIES |
CHLORINATED POLYVINYL CHLORIDE (CPVC) PIPES FOR POTABLE HOT AND COLD WATER DISTRIBUTION SUPPLIES |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 7.1 (Mean Outside Diameter as per IS:15778:2007) |
500.0 |
|
| 7.1.1 (Outside Dia. at any point as per IS:15778:2007) |
500.0 |
|
| 7.1.1 (Max. Outside Dia. at any point as per IS:15778:2007) |
500.0 |
|
| 7.1.1 (Min. Outside Dia. at any point as per IS:15778:2007) |
500.0 |
|
| 7.1.2 (Average Wall Thickness as per IS:15778:2007) |
1000.0 |
|
| 7.1.2 (Min. Wall Thickness as per IS:15778) |
500.0 |
|
| 7.1.2 (Max. Wall Thickness as per IS:15778) |
500.0 |
|
| 9.4 (Reversion Test as per IS:12235(Part-5/sec.1)) |
1000.0 |
|
| 9.1 (Visual Appearance as per IS:15778) |
1000.0 |
|
| 9.5 (Vicat softening Temperature as per IS:12235(Part-2)) |
1000.0 |
|
| 9.6 (Density as per IS:12235 (Part-14)) |
2000.0 |
|
|
| 22 |
IS 1664 (2002) - Mineral mixtures for supplementing cattle feeds - Specification (Fourth Revision) |
Mineral mixtures for supplementing cattle feeds - Specification (Fourth Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 23 |
AASHTO T 166 (for BC & DBM cores) - AASHTO T 166-Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated Surface-Dry Specimens |
AASHTO T 166-Standard Method of Test for Bulk Specific Gravity (Gmb) of Compacted Asphalt Mixtures Using Saturated Surface-Dry Specimens |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 24 |
IS 2052 (2023) - Compounded Feeds for Cattle — Specification |
Compounded Feeds for Cattle — Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
No Record Found
|
|
| 25 |
IS 278 (2009) - Galvanized steel barbed wire for fencing - Specification (Fourth Revision) |
Galvanized steel barbed wire for fencing - Specification (Fourth Revision) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 12.1 (Breaking Load of Completed Barbed Wire) |
1000.0 |
|
| 12.2.1 (Zinc Coating of Line wire) |
2000.0 |
|
| 12.2.2 (Zinc Coating of Point wire) |
2000.0 |
|
|
| 26 |
IS 13757-1993 RA 2011 (1993 RA 2011) - Burnt Clay Fly Ash Building Bricks-specification |
Burnt Clay Fly Ash Building Bricks-specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 6.0 Dimensions and Tolerances (Length, Width, Height mm) |
1000.0 |
|
| 7.1 Compressive strength (Compressive strength) |
2000.0 |
|
| 7.2 Water Absorption (Water absorption, %) |
1000.0 |
|
| 7.3 Efflorescence (Efflorescence) |
1000.0 |
|
|
| 27 |
IS 14223 (Part 1):2023 - Polished Building Stones —Specification (Part 1-Granite and Similar Stones) |
Polished Building Stones —Specification (Part 1-Granite and Similar Stones) |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5,Table 1-(i) (Specific gravity ( as per IS 1124)) |
1000.0 |
|
| 5,Table-1(ii) (Water absorption (as per IS 1124)) |
1000.0 |
|
| 5,Table-1(vi) (Hardness, in Mohs (as per IS 13630 (Part 13))) |
2000.0 |
|
|
| 28 |
1121 (Stone) (1974) - Method of Test of Natural Building Stone |
Method of Test of Natural Building Stone |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5 (Compressive Strength (Dry Condition), [IS 1121 (Part 1): 1974], N/mm^2) |
3000.0 |
|
| 5 (Compressive Strength (Wet Condition), [IS 1121 (Part 1): 1974], N/mm^2) |
3000.0 |
|
| 5 & 6 (Water Absorption [IS 1124 : 1974], %) |
1000.0 |
|
| 5 & 6 (Specific Gravity [ IS 1124 : 1974]) |
1000.0 |
|
| 13 (Mohs Hardness [ IS 13630 (Part 13) 2019]) |
2000.0 |
|
| 5 & 6 (Porosity [IS 1124 : 1974], %) |
1000.0 |
|
|
| 29 |
IS:8-1994 (1994) - High Heat Duty Fireclay Refractories |
High Heat Duty Fireclay Refractories |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 4.0 (Loss on Ignition, %) |
1000.0 |
|
| 5.0 (Silica, %) |
1000.0 |
|
| 6.0 (Alumina, %) |
1000.0 |
|
| 7.0 (Iron (as Ferric Oxide), %) |
1000.0 |
|
| 8.0 (Titania, %) |
1000.0 |
|
| 9.1 (Calcium Oxide, %) |
1000.0 |
|
| 9.2 (Magnesium Oxide, %) |
1000.0 |
|
| Part 4 of IS:1528 (Compressive Strength on the lines of Part 4 of IS:1528) |
2000.0 |
|
|
| 30 |
IS 854 (2021) - Textiles Handloom cotton turkish honeycomb and huckaback towels and towelling cloth Specification |
Textiles Handloom cotton turkish honeycomb and huckaback towels and towelling cloth Specification |
- View breakup
-
| Clause No. |
Testing Charges (Excl. Of Taxes) |
NABL |
| 5.1 (Count of Yarn (Warp)) |
500.0 |
|
| 5.1 (Count of yarn (Weft)) |
500.0 |
|
| 5.1 (Ends/dm) |
500.0 |
|
| 5.1 (Picks/dm) |
500.0 |
|
| 5.1 (Mass) |
1000.0 |
|
| 5.1 (Weave) |
500.0 |
|
| 5.1 (Breaking Load (Warp)) |
1000.0 |
|
| 5.1 (Breaking Load (Weft)) |
1000.0 |
|
| 5.2 (Identification of material) |
2000.0 |
|
| 5.2 (Dimensional Change) |
2000.0 |
|
| 5.2 (Scouring loss) |
2000.0 |
|
| 5.2 (Color fastness to light) |
3000.0 |
|
| 5.2 (Color fastness to washing) |
2000.0 |
|
| 5.2 (Color fastness to rubbing) |
2000.0 |
|
| 5.2 (Wettability) |
1000.0 |
|
|
