NTH - Management Information System

National Test House (ER), Kolkata

Block-C.P, Sector-V, Salt Lake City, Kolkata, West Bengal - 700091, Kolkata, Kolkata, West Bengal, 700091

- director-kol[at]nth[dot]gov[dot]in

Scope List

Reset

1301 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

IS 2932 (2013) - Enamel, Synthetic, Exterior : (a) Undercoating (b) Finishing

Enamel, Synthetic, Exterior : (a) Undercoating (b) Finishing

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) ( 501kVA TO 1000 kVA ) [501kVA TO 1000 kVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) ( 501kVA TO 1000 kVA )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.3(b) (Temperature Rise Test)	35000.0
21.2(a) (Measurement of Winding Resistance)	1000.0
21.2(b) (Measurement of voltage ratio and, check of voltage vector relationship)	1500.0
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	15000.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	5000.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	7000.0
21.2(c) (Measurement of impedance voltage (principal tapping), short circuit impedance and load loss (At 50% and 100% load))	7000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	20000.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	1500.0
21.2(d) (Measurement of no Load and loss and current)	6000.0
21.2(f) (lnduced Over Voltage withstand test)	3000.0
21.4(a) (Determination of sound levels)	6000.0
21.4( e) (BDV of Oil in the transformer)	10000.0
21.2(g) (AC High Voltage Withstand Test)	2500.0
As per CBIP Manual No. 317 Cl. (Harmonics of No-load Current)	12000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	5000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	5000.0
N.A. (Unbalance Current)	5000.0

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) ( 201kVA TO 500kVA ) [201kVA TO 500kVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) ( 201kVA TO 500kVA )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.3(b) (Temperature Rise Test)	30000.0
21.2(a) (Measurement of Winding Resistance)	1000.0
21.2(b) (Measurement of voltage ratio and, check of voltage vector relationship)	1500.0
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	15000.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	5000.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	7000.0
21.2(c) (Measurement of impedance voltage (principal tapping), short circuit impedance and load loss (At 50% and 100% load))	6000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	15000.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	1000.0
21.2(d) (Measurement of no Load and loss and current)	5500.0
21.2(f) (lnduced Over Voltage withstand test)	2500.0
21.4(a) (Determination of sound levels)	6000.0
21.4( e) (BDV of Oil in the tranformer)	10000.0
21.2(g) (AC High Voltage Withstand Test)	2500.0
As per CBIP Manual No. 317 Cl (Harmonics of No-load Current)	12000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	4000.0
As per CBIP No. 317 Cl. 3.10 (Magnetic Balance Test)	4000.0
N.A. (Unbalance Current)	4000.0

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) Three Phase ( 1 kVA to 200KVA ) [1kVA to 200KVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) Three Phase ( 1 kVA to 200KVA )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.3(b) (Temperature Rise Test)	24000.0
21.2(a) (Measurement of Winding Resistance)	1000.0
21.2(b) (Measurement of voltage ratio and, check of voltage vector relationship)	1500.0
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	10000.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	5000.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	7000.0
21.2(c) (Measurement of impedance voltage (principal tapping), short circuit impedance and load loss (At 50% and 100% load))	5000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	10000.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	1000.0
21.2(d) (Measurement of no Load and loss and current)	5500.0
21.2(f) (lnduced Over Voltage withstand test)	2500.0
21.4(a) (Determination of sound levels)	5000.0
21.4( e) (BDV of Oil in the tranformer)	10000.0
21.2(g) (AC High Voltage Withstand Test)	2500.0
As per CBIP Pub No. 317 Cl. 3.17 (Magnetic Balance Test)	3000.0
As per CBIP Manual No. 317 Cl (Harmonics of No-load Current)	10000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	3000.0
N.A. (Unbalance Current)	3000.0

IS 1180 : Part 1 (2014) - Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) Single Phase ( 1kVA to 100kVA ) [1kVA to 100kVA]

Outdoor Type Oil Immersed Distribution Transformers - Specification Part 1 Mineral Oil Immersed (Fourth Revision) Single Phase ( 1kVA to 100kVA )

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
21.3(b) (Temperature Rise Test)	15000.0
21.2(a) (Measurement of Winding Resistance)	700.0
21.2(b) (Measurement of voltage ratio and, check of voltage vector relationship)	700.0
21.5.1.121.5.2.121.5.3.1 (Vacuum Pressure (Type Test))	6000.0
21.5.1.221.5.2.221.5.3.2 (Pressure test (routine))	3500.0
21.4.(d) (Adhesion by Tape Test)	5000.0
21.5.1.321.5.2.321.5.3.3 (Oil leakage test)	5000.0
21.2(c) (Measurement of impedance voltage (principal tapping), short circuit impedance and load loss (At 50% and 100% load))	3000.0
7.9 & 8.9 (Measurement of Permissible flux density and over fluxing)	6500.0
21.4( c) (Measurement of No load current at 112.5 percent voltage)	2000.0
21.2(e) (Measurement of insulation resistance)	700.0
21.2(d) (Measurement of no Load and loss and current)	3000.0
21.2(f) (lnduced Over Voltage withstand test)	1200.0
21.4(a) (Determination of sound levels)	5000.0
21.4( e) (BDV of Oil in the tranformer)	10000.0
21.2(g) (AC High Voltage Withstand Test)	1200.0
As per CBIP Pub No. 317 Cl. 3.17 (Magnetic Balance Test)	2000.0
As per CBIP Manual No. 317 Cl (Harmonics of No-load Current)	6000.0
As per CBIP No. 317 Cl. 3.10 (Zero Sequence Impedance Measurement)	2000.0
N.A. (Unbalance Current)	2000.0

Custom Paint 2025 - Custom Paint System

Custom Paint System

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Pull out Test of paint coating on cementitious surface)	2000.0
2 (Accelerated Weathering Test for 96 hrs)	4800.0
3 (Water Permeability Test)	5000.0
4 (BS 476 Part 7 & Customers Specification)	10000.0
5 (Pull of adhesion)	5000.0
6 (Abrasion Resistance)	5000.0
7 (Water absorption /resistance to Water test)	1200.0
8 (Tensile strength)	2000.0
9 (Chemical Resistance Tests (24 hrs))	10000.0
10 (Cathodic Disbondment Test)	5000.0

Custom Standard For Epoxy Coating System. (2025) - Custom Standard For Epoxy Coating System.

Custom Standard For Epoxy Coating System.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (1 25% NaOH Solution 2 30 % H2SO4 Solution 3 20 % HCL solution 4 Tap Water 5 Acetone 6 Ethanol 7 20% Acetic acid 8 Toluene 9 Carbon Tetra Chloride - CCL4 10 Cotton seed oil 11 20% KOH 12 20% Na2CO3 Solution)	14400.0
2 (30 % H2SO4 Solution)	1200.0
3 (20 % HCL solution)	1200.0

F-7 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-7 High build coal tar epoxy Coating

F-7 High build coal tar epoxy Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Therotical Covering capacity in sq.mt/coat/litres.)	1500.0
4 (Weight per Litres)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-9 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-9 Inorganic zinc silicate Coating

F-9 Inorganic zinc silicate Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg. C)	1200.0
7 (Pot Life at 30 deg.C for Two Component Paints)	1200.0
8 (Adhesion (ASTM D 4541))	5000.0
9 (Over-coat interval)	1200.0
10 (Temperature Resistance (Min))	3000.0

F-11 EIL Specification No. 6-79-0020 Rev.1 - F-11 Heat Resistance synthetic medium based Two pack Aluminium paint

F-11 Heat Resistance synthetic medium based Two pack Aluminium paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (.Therotical Covering capacity in sq.mt/coat/litres.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.C)	1200.0
7 (Over-coat interval)	1200.0
8 (Temperature Resistance (Min))	1200.0

F14 EIL Specification No. 6-79-0020 Rev.1 (2014) - F-14 Polyamine cure coal tar epoxy

F-14 Polyamine cure coal tar epoxy

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-12 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-12 Heat Resistance Silicon Aluminium paint

F-12 Heat Resistance Silicon Aluminium paint

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Therotical Covering capacity in sq.mt/coat/litres)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Over-coat interval)	1200.0
8 (Temperature Resistance (Min))	3000.0

F-15 EIL Specification No. 6-79-0020 Rev.1 - F-15, Two Component Epoxy Phenolic Coating Cured with Polyamine adduct Hardener

F-15, Two Component Epoxy Phenolic Coating Cured with Polyamine adduct Hardener

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.C)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-17 EIL Specification No. 6-79-0020 Rev.1 (2024) - F-17 Novolac Epoxy Phenolic Coating Cured with Polyamine Adduct Hardener

F-17 Novolac Epoxy Phenolic Coating Cured with Polyamine Adduct Hardener

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.C)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-6A EIL Specification No. 6-79-0020 Rev.1 (2024) - F-6A Epoxy High Build Coating

F-6A Epoxy High Build Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

F-6B EIL Specification No. 6-79-0020 Rev.1 (2024) - F-6B Epoxy High Build Coating

F-6B Epoxy High Build Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0

IS 398 : Part 4 (1994) - Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.2 (Breaking load test of individual Aluminium Alloy wire (7 wire construction))	1000.0
12.3 (Elongation test of Aluminium Alloy wire(7 wire construction))	1000.0
12.4 (Resistance test of Aluminium Alloy wire(7 wire construction))	1000.0
12.2 (Breaking load test of individual Aluminium Alloy wire (19 wire construction))	2000.0
12.3 (Elongation test of Aluminium Alloy wire(19 wire construction))	2000.0
12.4 (Resistance test of Aluminium Alloy wire (19 wire construction))	2000.0

F-6C EIL Specification No. 6-79-0020 Rev.1 (2024) - F-6C Solvent less epoxy Coating

F-6C Solvent less epoxy Coating

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Volume Solid)	2000.0
2 (Dry Film Thickness)	1200.0
3 (Theoretical Covering capacity in sq.mt/coat/litre.)	1500.0
4 (Weight per Litre)	1200.0
5 (Touch dry at 30 deg.C)	1200.0
6 (Hard Dry at 30 deg.c)	1200.0
7 (Full cure at 30 deg.C)	1200.0
8 (Over-coat interval)	1200.0
9 (Pot Life at 30 deg.C for Two Component Paints)	1500.0
10 (Adhesion (ASTM D 4541))	5000.0
11 (Temperature Resistance (Min))	3000.0
1 ()	-

IS 398 : Part 3 (1976) - Specification for aluminium conductors for overhead transmission purposes: Part 3 aluminium conductors, aluminized steel reinforced (Second Revision)

Specification for aluminium conductors for overhead transmission purposes: Part 3 aluminium conductors, aluminized steel reinforced (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Test results for all mechanical parameters)	14000.0

IS 398 : Part 1 (1996) - Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
12.6(2) (Measurement of lay ratio-Outer layer(19 wire construction))	1500.0
12.2 (Measurement of diameter of Aluminium wire(7 wire construction))	1000.0
12.3 (Breaking load test of individual Aluminium(7 wire construction))	1000.0
12.4 (Wrapping test of Aluminium wire (7 wire construction))	1000.0
12.5 (Resistance test of Aluminium wire(7 wire construction))	1000.0
12.6 (Measurement of lay ratio (7 wire construction))	1000.0
12.2 (Measurement of diameter of Aluminium wire(19 wire construction))	3000.0
12.3 (Breaking load test of individual Aluminium (19 wire construction))	3000.0
12.4 (Wrapping test of Aluminium wire(19 wire construction))	3000.0
12.5 (Resistance test of Aluminium wire(19 wire construction))	3000.0
12.6(1) (Measurement of lay ratio-Inner layer(19 wire construction))	1500.0

IS 2932 : 2025 (2025) - Air Drying Enamel Paint for Architectural and Industrial Applications- Specification

Air Drying Enamel Paint for Architectural and Industrial Applications- Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

#IS 15489:2024 (2024) - Plastic Emulsion paint Full specification Except Keeping property 12 months

Plastic Emulsion paint Full specification Except Keeping property 12 months

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 6.2 (Conditions in the container)	500.0
Cl 6.3 (Thinning)	500.0
Cl 6.4 (Application Properties)	500.0
Cl 6.5 (Mass in Kg/10L)	500.0
Cl 6.6 (Opacity)	500.0
Cl 6.7 (Fastness to Light)	25000.0
Cl 6.9 (Lead Restriction)	1000.0
Cl 6.8 (Durability Test)	20000.0
Cl 6.10.i (Consistency)	500.0
Cl 6.10 ii (a) (Drying Time: a) Surface Dry)	500.0
Cl 6.10 ii (b) (Drying Time: b) Hard Dry)	500.0
Cl 6.10 iii (Finish)	500.0
Cl 6.10 iv (Gloss at 60 degree)	500.0
Cl 6.10 v (Colour)	500.0
Cl 6.10 vii (Resistance to Alkali)	1000.0
Cl 6.10 viii (Washability and Cleanability)	1000.0
Cl 6.10 ix (Accelerated storage stability)	1000.0
Cl 6.10 x (Recoating Properties)	1000.0
Cl 6.12.2.2 (Toxic Elements Lead Cadmium Chromium VI)	3000.0
Cl 6.10 xi (Volatile organic compound (VOC))	4000.0

RDSO/PE/SPEC/TL/0040 (Rev-2)-2021 - Specification for Low MAintenance Lead Acid 40Ah, 150 Ah, 200 Ah and 250 Ah for Traction Distribution System

Specification for Low MAintenance Lead Acid 40Ah, 150 Ah, 200 Ah and 250 Ah for Traction Distribution System

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.12 (Air Pressure Test)	10000.0
7.5 (Capacity at 10 hrs rate)	25000.0
4.2 (Dimensions,Mass, markings and Workmanship)	3000.0
7.11 (Equilibrium Float Current)	10000.0
7.8 (Life Test)	90000.0
7.13 (Material and Component Specification Verification Test)	2000.0
7.7 (Retention of Charge)	20000.0
7.9 (Storage Test)	10000.0
7.6 (Watt Hour and Ampere Hour Efficiency Test)	10000.0
7.10 (Loss of Water Test)	10000.0
Cl.11 of IEC-60896-11:2002 (Short Circuit Current and Internal Resistance)	20000.0

6047 (2009) - Scouring products for utensil cleaning - Specification

Scouring products for utensil cleaning - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 6.1 (Tensile Strength of Edge/Selvedge Wire (steel))	2000.0
Cl 6.1 (Tensile Strength of Lacing Wire(steel))	2000.0
Cl 6.1 (Tensile Strength of Mesh Wire(Steel))	2000.0
Cl 6.1 (Elongation of Edge/Selvedge Wire)	1000.0
Cl 6.1 (Elongation of Lacing Wire)	1000.0
Cl 6.1 (Elongation of Mesh Wire(Steel))	1000.0
Cl 5.1 (Diameter of Lacing Wire without Polymer Coating)	500.0
Cl 5.1 (Diameter of Edge/Selvedge Wire without Polymer Coating)	500.0
Cl 5.1 (Diameter of Mesh Wire without Polymer Coating)	500.0
Cl 8.9 (Size of Gabbion Box)	1500.0
Cl 3.14 (Mesh Size)	1000.0
Cl 5.1 (Chemical analysis)	2500.0
Cl 9 (Workmanship)	1000.0
Cl 7.1 (Galvanising)	2000.0
Cl 5 (Mass of Zinc Coating of Mesh Wire)	2000.0
Cl 5 (Mass of Zinc of Edge/Selvedge Wire)	2000.0
Cl 5 (Mass of Zinc Coating of Lacing Wire)	2000.0
Cl 7.2 (Hardness of polymer Coating)	2000.0
Cl 7.2 (Specific Gravity)	2000.0
Cl 7.2 (Tensile strength of PVC coating)	3000.0

#IS 8329 - DI Pipe

DI Pipe

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 13 (External Diameter)	500.0
Cl B-7 (Bore Clearence)	500.0
Cl 3.2.2 (Ovality of Pipe)	500.0
Cl 13.3 (Wall Thickness)	500.0
Cl B-6 (Thickness of Lining)	500.0
Cl 3.21 (Length)	1000.0
Cl 10.2 (Hardness test)	2000.0
Cl 10.1.1 (Tensile Test)	3000.0
Cl 16.2 (Bituminous Coating)	2500.0

# IS 10748 - HOT-ROLLED STEEL STRIP FOR WELDED TUBES AND PIPES

HOT-ROLLED STEEL STRIP FOR WELDED TUBES AND PIPES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 11 (Freedom form defects)	1000.0
Cl 12 (Dimensions)	1000.0
Cl 8 (Tensile test)	3000.0
Cl 9 (Bend Test)	1000.0
Cl 7 (Chemical analysis)	3000.0

# IS 5522 - STAINLESS STEEL SHEETS AND STRIPS FOR UTENSILS - SPECIFICATION

STAINLESS STEEL SHEETS AND STRIPS FOR UTENSILS - SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 6 (Freedom form defects)	1000.0
Cl 9 (Dimensions)	2000.0
Cl 8.2 (Tensile test)	3000.0
Cl 8.3 (Hardness Test)	2000.0
Cl 8.5 (Ericbsen Cupping Test)	1000.0
Cl 7 (Chemical analysis)	4000.0

# IS 513 (2016) - Cold Reduced Carbon Steel Sheet and Strip

Cold Reduced Carbon Steel Sheet and Strip

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 9 (Visual Examination)	1000.0
Cl 10 (Dimension)	1000.0
Cl 7.1 (Tensile test)	3000.0
Cl 7.2 (Bend test)	1000.0
Cl 6 (Chemical Composition)	2500.0

# IS 4454(part1) - Steel Wire for cold formed springs

Steel Wire for cold formed springs

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 9 (Dimensions)	1000.0
Cl 10.1 (Tensile)	3000.0
Cl 10.2 (Torsion test / wrapping test)	1000.0
Cl 7 (Chemical analysis)	3000.0

#IS 1363/1367 - Bolts / Nuts

Bolts / Nuts

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl.9.2 (Proof test)	3000.0
Cl 7 table 3 (Hardness test)	2000.0
Cl 9.2 (Ultimate Tensile load)	2000.0
Cl.9.2 (Tensile Strength)	1000.0
Cl.9.14 (Charpy Impact Test)	5000.0
Cl 8 (Dimensions)	1500.0

1
2
3
Next
Last