NTH - Management Information System

National Test House (WR), Mumbai

Plot No. F 10, M.I.D.C, Marol, Andheri (E), Mumbai Maharashtra - 400093, Mumbai, Mumbai, Maharashtra, 400093

28260927 director-mum[at]nth[dot]gov[dot]in

Scope List

Reset

848 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

Prestressing hardware - Prestressing hardware ( Anchor head, Barrel, Bearing Plate, Wedge, Trumpet cone and HDPE Sheathing)

Prestressing hardware ( Anchor head, Barrel, Bearing Plate, Wedge, Trumpet cone and HDPE Sheathing)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.1.1 (Ultrasound test of Anchor head)	4000.0
1.1.2 (Chemical Analysis of Anchor head)	3000.0
1.1.3 (Dimension test of Anchor head)	1000.0
1.1.4 (Hardness test of Anchor Head)	2000.0
1.2.1 (Chemical Analysis of Barrel)	5000.0
1.2.2 (Dimension test of Barrel)	1000.0
1.3.3 (Hardness test of Bearing Plate)	2000.0
1.3.1 (Chemical Analysis of Bearing plate)	3000.0
1.3.2 (Dimension test of Bearing plate)	1000.0
1.3.3 (Hardness test of Bearing Plate)	2000.0
1.4.1 (Dimension test of Wedge)	1000.0
1.4.2 (Surface hardness of Wedge)	2000.0
1.4.3 (load test of Wedge)	3000.0
1.5.1 (Dimension test of Trumpet cone)	1000.0
1.5.2 (Chemical test of Trumpet cone)	3000.0
1.0 (Test of HDPE Sheathing)	21000.0

1-Custom - Self Drilling anchors

Self Drilling anchors

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

IS 210 (2009) - Grey iron castings - Specification (First Revision)

Grey iron castings - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
16 (Brinell Hardness)	2000.0
15 (Tensile Strength)	2500.0
6 (Chemical Composition (Sulphur))	500.0
6 (Chemical Composition (Phosphorus))	1000.0
9 (Microstructure)	3000.0

#IS 210 - Grey Cast Iron

Grey Cast Iron

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl.15 (Tensile test )	2500.0
Cl.9 (Microstructure )	2000.0
Cl.10 (Freedom from defect )	1000.0
Cl.17 (Transverse test )	3000.0
Cl.6 (Chemical Test(Optional) )	1200.0
Cl.16 (Hardness test )	2000.0

Fastener as per ISO/EN/BS EN - Mechanical properties of Fastener as per ISO 898 (Part- 1, 2), EN 14399 (P-3,5,9), ISO 10683

Mechanical properties of Fastener as per ISO 898 (Part- 1, 2), EN 14399 (P-3,5,9), ISO 10683

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Proof Load, kN)	3000.0
7.2 (Hardness)	2000.0
7.3 (Surface Integrity)	2000.0
7.4 (Depth of Decarburisation)	2000.0
7.5 (Coating Thickness, micron)	2000.0
7.6 (Adhesion test)	1000.0
6 (Chemical composition, % by mass)	2500.0
5.1 (Wedge Load Test)	3000.0
5.2 (Tensile test- TS, YS, %E and RoA)	4000.0
5.4 (Charpy Impact Test, At -20 deg C)	3000.0
5.5 (Compression load Test)	3000.0
5.5 (Dimensions, mm)	2000.0

Custom-Mech-NR - Custom-Mech-NR

Custom-Mech-NR

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

# IS 16651 - SS Rebar (28 -32 mm)

SS Rebar (28 -32 mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 7.2 (Mass per meter run)	1000.0
Cl 9.2 (Tensile test)	3500.0
Cl 9.3 (Bend test)	1000.0
Cl 9.4 (Rebend test)	1500.0
Cl 5.7 (Pull out test)	15000.0
Cl 5.2 (Rib area)	1000.0
Cl 8.6 (Impact Test for Grade D,E,F (dia 16mm above))	3000.0
Cl 4 (Chemcial Analysis with Micro Alloys & CE)	5000.0
Cl 8.7 (Intergranular Corrosion Test -IGC -(Option))	10000.0

# IS 16651 - SS Rebar ( 12 - 28 mm)

SS Rebar ( 12 - 28 mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

# IS 16651 - SS Rebar ( 0-12 mm)

SS Rebar ( 0-12 mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 7.2 (Mass per meter run)	1000.0
Cl 9.2 (Tensile test)	2000.0
Cl 9.3 (Bend test)	1000.0
Cl 9.4 (Rebend test)	1000.0
Cl 5.7 (Pull out test)	10000.0
Cl 5.2 (Rib area)	1000.0
Cl 4.3.1 (Chemcial Analysis with Micro Alloys & CE)	5000.0
Cl 8.7 (Intergranular Corrosion Test -IGC -(Option))	10000.0

IS 2250/On the lines of ASTM/IS 1727/2770 - MICRO CONCRETE

MICRO CONCRETE

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
custom (Flow Test(on the lines of IS 2250))	1000.0
custom (Compressive strength (on the lines of IS /ASTM)-1 Day)	2000.0
custom (Compressive strength (on the lines of IS /ASTM)-7 Days)	2000.0
custom (Compressive strength (on the lines of IS /ASTM)-28 Days)	2000.0
custom (Flexural strength -(on the lines of IS/ASTM)1 Day)	2000.0
custom (Flexural strength (on the lines of IS /ASTM)-7 Days)	2000.0
custom (Flexural strength (on the lines of IS /ASTM)-28 Days)	2000.0
custom (Drying Shrinkage (IS 1727))	1000.0
custom (Split Tensile strength (IS 5816))	2000.0
custom (Scratch Hardness-Mohs' scale(-on the lines of IS 13630(13)))	1500.0
custom (Co-efficient of Thermal Expansion(IS /ASTM))	3000.0

IS 2250:1981 - Code of Practice for Preparation and use of Masonry Mortars

Code of Practice for Preparation and use of Masonry Mortars

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
2.4,6.1, Table 1 & Appendix A (Compressive strength of Masonry Mortar)	4000.0
9.1.1 Table 1,Appendix B (Consistency of Masonry Mortar)	500.0
6,Table 1 (Grade of Mortar-Mortar mix ratio (IS 1199))	5000.0
Custom ( ref 5.1.4) (Sulphate content)	1200.0
Custom (Chloride content)	1200.0
custom (Bulk density-kg/cum:{on the lines of IS 2386(III)})	500.0
custom (Tensile strength (on the lines of IS 15477))	4000.0
custom (Pot life (on the lines of IS 5410))	1000.0

CSD Samples - CSD Samples : Test as per CSD Data sheet

CSD Samples : Test as per CSD Data sheet

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Automatic cooker-Tests as per IS: 11879: 1986)	20000.0
2 (LED Bulb Test as per CSD Data Sheet & IS: 302-1:2008)	4000.0
3 (Performance / Functional Tests as per relevant IS Specification of IS 4280:1980 (or) CSD Technical data Specification.)	20000.0
4 (Performance / Functional Tests as per relevant IS 11514 (or) Technical data Specification.)	7000.0
5 (Performance / Functional Tests as per relevant IS 366 (or) Technical data Specification.)	10000.0
6 (Test as per IS: 374 -1979, Reaffirmed 2007 (Up to amendment 8))	8000.0
7 (All possible Performance / Functional Tests as per relevant IS 302-2-6 : 2009 or IS 2994 (or) Technical data Specification.)	8000.0
8 (All possible Performance / Functional Tests as per relevant IS 302-2-9 : 2009 (or) Technical data Specification.)	8000.0
9 (All possible Performance / Functional Tests as per relevant IS 8144 : 1997 (or) Technical data Specification.)	7000.0
10 (All possible Performance / Functional Tests as per IS 368 (1992): Electric Immersion Water Heaters)	14000.0

#IS 6003 - Indented Wire for Prestressed Concrete

Indented Wire for Prestressed Concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 5.1 (Dimensions)	1000.0
Cl 5.2 (Geometric consideration)	1000.0
Cl 7.1 (Tensile test)	3000.0
Cl 8.5 (Reverse bend test)	1500.0
Cl 8.7 (Relaxation Test (Optional))	1000.0
Cl 4 (Chemical analysis)	1000.0

#IS 6006 - Uncoated Stress Relieved Strand for prestressed concrete

Uncoated Stress Relieved Strand for prestressed concrete

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl 4.5 (Workmanship and finish)	1000.0
Cl 5 (Dimensions)	1000.0
Cl 8.2 (Tensile test)	5000.0
Cl 8.5 (Relaxation Test)	1000.0
Cl 4.1.2 (Chemical analysis)	1000.0

#IS 1786 - HSD Bar (28 -32 mm)

HSD Bar (28 -32 mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl.3 (Mass per meter run)	1000.0
Cl 9.2 (Tensile test)	3500.0
Cl.9.3 (Bend test)	1000.0
Cl.9.4 (Rebend test)	1500.0
Cl.5.7 (Pull out test (Fee Ratio 70:30 among Mechanical & Civil))	15000.0
Cl.8 (Rib area)	1000.0
Cl.8 (TS/YS Ratio)	500.0
Cl.5 (Total Elongation at Maximum Force)	500.0
Cl.4.2 (Chemical analysis without CE)	2000.0
Cl.4.2 (HSDS Bar (C, S, P, & S+P, CE))	2500.0
Cl.4.2 (Chemical Analysis with Micro Alloys without CE)	4000.0
Cl.4.2 (Chemical Analysis with Micro Alloys & CE / Chemical Analysis including CE)	4500.0
Cl 9.1.3 (Phase Distribution - TM Ring test (Optional))	3000.0

#IS 1786 - HSD Bar (12 - 28 mm)

HSD Bar (12 - 28 mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl.3 (Mass per meter run)	1000.0
Cl.9.2 (Tensile test)	3000.0
Cl.9.3 (Bend test)	1000.0
Cl.9.4 (Pull out test (Fee Ratio 70:30 among Mechanical & Civil))	15000.0
Cl.5.7 (Rebend test)	1000.0
Cl.5 (Rib area)	1000.0
Cl.4.2 (Chemical analysis without CE)	2000.0
Cl.4.2 (HSDS Bar (C, S, P, & S+P, CE))	2500.0
Cl.4.2 (Chemical Analysis with Micro Alloys without CE)	4000.0
Cl.4.2 (Chemical Analysis with Micro Alloys & CE / Chemical Analysis including CE)	4500.0
Cl 9.1.3 (Phase Distribution - TM Ring test (Optional))	1000.0
4.2 (carbon by mass)	500.0
4.2 (sulphur)	500.0
4.2 (Phosphorus)	500.0
4.2 (Sulphur plus Phosphorus)	500.0
4.2 (C.E.)	500.0
Cl.8 ()	500.0

#IS 1786 - HSD Bar (up to 12 mm)

HSD Bar (up to 12 mm)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl.3 (Mass per meter run)	1000.0
Cl.9.2 (Tensile test)	2000.0
Cl.9.3 (Bend test)	1000.0
Cl.9.4 (Rebend test)	1000.0
Cl.5.7 (Pull out test (Fee Ratio 70:30 among Mechanical & Civil))	10000.0
Cl.8 (TS/YS Ratio)	500.0
Cl.8 (Total Elongation at Maximum Force)	500.0
Cl.5 (Rib area)	1000.0
Cl.4.2 (Chemical analysis without CE)	2000.0
Cl.4.2 (HSDS Bar (C, S, P, & S+P, CE))	2500.0
Cl.4.2 (Chemical Analysis with Micro Alloys without CE)	4000.0
Cl 9.1.3 (Phase Distribution - TM Ring test (Optional))	3000.0

NTH/WI/MC (On the lines of DKD-R 6-1:01/2014) 8 - Calibration of Pressure Gauges

Calibration of Pressure Gauges

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.1 (Industrial pressure gauge calibration)	1200.0

NTH_CUSTOM/2026/025 - PROFICIENCY TESTING FOR RUBBER

PROFICIENCY TESTING FOR RUBBER

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Tensile Strength)	-
- (Tear Strength)	-
- (Shore A hardness (Durometer hardness))	-
- (Ash Contents)	-
- (Density)	-
- (Carbon Black Contents)	-

NTH_CUSTOM/2026/024 - ASTM D 1248

ASTM D 1248

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (Description of the sample )	500.0
- (Density)	1000.0
- (Water absorption for 24 hours )	1000.0
- (Water absorption (Long term immersion))	4000.0

NTH_CUSTOM/2026/023 - IBR 1950

IBR 1950

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Duplicate Test Certificate)	1200.0

MMDTS 18034 REV-02 - Developmental Technical specification for PU Based Wet-On-Wet applicable Exterior Painting System for LHB Type Coaches.

Developmental Technical specification for PU Based Wet-On-Wet applicable Exterior Painting System for LHB Type Coaches.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (ANTI-GRAFFITI TEST,ASTM D-6578)	5000.0
2 (Dry Film thickness)	1200.0
3 (Weathering resistance (QUV 1000 hrs))	50000.0
4 (Corrosion resistance (ASTM B117, 1000 hrs))	50000.0

MMDTS 18034 Rev.05 - Technical specification for PU based Wet-on-Wet applicable Exterior Painting System of LHB type coaches

Technical specification for PU based Wet-on-Wet applicable Exterior Painting System of LHB type coaches

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
3.X (Anti-graffiti Test)	5000.0
3.VIII (Cyclic Corrosion (ISO-11997-1 Cycle A for 1000 hours))	50000.0
3.IX (Distinctness of Image (DOI))	10000.0

MMDTS 18034 (Rev. 04) (2019) - Technical Specification for PU based Wet -On- Wet Applicable on Exterior Painting System for LHB Types Coaches.

Technical Specification for PU based Wet -On- Wet Applicable on Exterior Painting System for LHB Types Coaches.

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

M&C/PCN/132/2021 - RDSO Specification for Painting of Helical Coils Springs of LHB Coaches and similar application (single pack)

RDSO Specification for Painting of Helical Coils Springs of LHB Coaches and similar application (single pack)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Drying Time (Hard Dry))	1200.0
3 (Finish)	1200.0
5 ((a) Dry Film thickness,(b) Cumulative DFT)	2400.0
15 (Mass in kg/10 litres.)	1200.0
14. e. (i) (Resistance to solvent (Acetone))	1500.0
14. e. (ii) (Resistance to solvent (Xylene))	1500.0
14.e.(iii) (Resistance to solvent (Ethanol))	1500.0
14.(f) (Resistance to Raw water/ Tape water)	1200.0
23 (Viscosity by Ford Cup no.4)	1200.0
6 (Volume solids %)	2000.0

AWWA C210 (2024) - Liquid - Epoxy Coatings and lining for Steel Water Pipe And fittings

Liquid - Epoxy Coatings and lining for Steel Water Pipe And fittings

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Additional Parameter (Colour)	1000.0
5.5.2 (Appearance)	1000.0
5.5.3 (Cure)	1000.0
5.5.4 (Dry Film Thickness)	1000.0
5.5.5 (Electrical Continuity)	5000.0
5.5.6 (Pull of adhesion)	5000.0
5.2.1 (Immersion & Vapor phase 30 days (DI Water))	2000.0
5.2.1 (Immersion & Vapor phase 30 days (Sulphuric acid 1% by wt.))	2000.0
5.2.1 (Immersion & Vapor phase 30 days (Sodium Hydroxide 1% by wt.))	2000.0
5.2.2 (Cathodic Disbondment Test)	5000.0
5.2.5 (Water Absorption)	2000.0
5.2.6 (Water Vapor Transmission)	5000.0
Additional parameter (Drinking water test (as per annex 1 of IS 16676 : 2017))	12000.0

NTH_CUSTOM/2026/022 - NPCIL SPECIFICATION ON EPOXY COATING FOR REACTOR BUILDING INTERNAL STRUCTURE AND EQUIPMENT

NPCIL SPECIFICATION ON EPOXY COATING FOR REACTOR BUILDING INTERNAL STRUCTURE AND EQUIPMENT

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Fineness of dispersion Hegmann gauge (0.004") with scale 0 to 8)	1200.0
2 (Volume solids (%))	2000.0
3 (Flash point Deg C)	1200.0
4 (Dry Film Thickness/coat in microns)	1200.0
5 (Pot life at 30 deg C)	1500.0
6 (Shelf life at 30 deg C)	1500.0
7 (Drying time in hrs a) Surface Dry)	1200.0
8 (Drying time in hrs b) Hard Dry)	1200.0
9 (Coverage (m²/litre))	1500.0
10 (Total dry film thickness in microns)	1200.0
11 (Colour)	1200.0
12 (Gloss (60 deg.))	1200.0
13 (Salt spray (21 days))	20000.0
14 (Protection against corrosion in humidity cabinet (21 Days))	15000.0
15 (Viscosity (Kinematic) at 25 deg C in stokes by Ford cup No. 4)	1200.0
16 (Scratch Hardness (kg))	1200.0
17 (Rocker hardness)	1500.0
18 (Practical Adhesion by sandwitch pull off technique)	4000.0
19 (Failure in cohesion in body/top coat)	4000.0
20 (Abrasion (Dry) resistance (mg/1000 cycle))	2000.0
21 (Water vapour permeability gm/m² - hr/mil)	5000.0
22 (Resistance to Distilled water - for 4 weeks)	3000.0
23 (Resistance to De ionised water - for 4 weeks)	3000.0
24 (Resistance to 2% Nitric Acid Solution for 4 weeks)	3000.0
25 (Resistance to 5% NaOH solution for 4 weeks)	3000.0
26 (Resistance to 5% detergent (eg. Teepol) for 4 weeks)	3000.0
27 (Resistance to Petrol - for 4 weeks)	4800.0
28 (Resistance to Hot water at 95 deg C - 1 hr for 40 cycles)	3000.0
29 (Accelerated weatherometer (500 hrs) by Fluorescent UV-Condensation Exposures)	20000.0
30 (Tensile Strength Kg/cm² ASTM D 2370)	1000.0
31 (% Elongation under load at the point of break ASTM D 2370 )	1000.0
32 (% Water absorption on free film (07 days) RRL Method Note 2)	2000.0

IS 398 Part 2 (2025) - ALUMINIUM CONDUCTORS FOR OVERHEAD TRANSMISSION PURPOSES

ALUMINIUM CONDUCTORS FOR OVERHEAD TRANSMISSION PURPOSES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Mechanical Test As per Annexure)	6000.0
0 (Resistance Test)	1000.0
13.6 (Resistance Test Clause 13.6 (Table 1))	2000.0
Annexure A-3 & Table 3 (Approximate breaking load of conductors)	2000.0
3.3 (Measurement of Diameter of individual Aluminum Wires)	3500.0

IS 398 : Part 1 (1996) - Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

IS 398 : Part 2 (1996) - Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (ACSR Conductor Acceptance & Type Tests)	34000.0
0 (ACSR Conductor Acceptance Tests)	14000.0
0 (ACSR Conductor Type Tests)	20000.0

1
2
3
Next
Last