NTH - Management Information System

National Test House (NWR), Jaipur

E-763, Road No. 9 F1 V.K.I.A Jaipur-302013, Rajasthan, Jaipur, Jaipur, Rajasthan, 302013

9717298334 nthjaipur-ca@nic.in

Scope List

Reset

290 Results

S.No.

Standard No.

Product

Testing Charges (Excl. Of Taxes)

Custom_4984-2016_MP_JalNigam (2025) - Custom_HDPE Pipe_4984-2016_MP_JalNigam

Custom_HDPE Pipe_4984-2016_MP_JalNigam

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.2 (IS:4984, Colour)	100.0
6.2.1 (IS:4984, Depth of strip)	100.0
6.2.1 (IS:4984, Width of Strip)	100.0
6.2.1 (IS:4984_Colour of Strip)	100.0
7.1 (IS:4984_Visual Appearance)	100.0
7.4 (IS:4984_Wall Thickness)	500.0
7.4.1 (IS:4984_Outside Diameter)	100.0
8.1 (IS:4984_Annexure-E_Pressure test)	5000.0
8.2 (IS:4984_Annex-F_Reversion Test)	1000.0
8.3 (IS:2530_Carbon Black Content)	1000.0
8.4 (IS:2530_Melt Flow Rate at 190 deg. Celcius and 5kgf)	1000.0
8.3 (IS:2530_Carbon Black Dispersion)	1000.0
7.4.1.2 (IS:4984_Ovality)	100.0
8.5 (IS:4984_Annex-B_OIT)	2000.0
8.7 (IS:7328_Density)	1000.0
8.9 (IS:4984_Annex-H_Tensile Strength)	1000.0
8.9 (IS:4984_Annex-H_Elongation at Break)	1000.0
8.6 (IS:9845_Overall Migration)	1000.0

Custom_14490_1997 - Custom specification_Railway_Bhopal

Custom specification_Railway_Bhopal

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.6 table-1 (13 of IS:1060(Part-2), Brightness)	2000.0

Custom-26-ER-LM - Lifting Sling Engine

Lifting Sling Engine

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

2025_Nircon Custom Specification - Nircon Custom Specification

Nircon Custom Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.0 (Tests)	10000.0

IS 6911 (2017) - Stainless steel plate, sheet and strip - Specification (Second Revision)

Stainless steel plate, sheet and strip - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Chemical Analysis (PLEASE SEE THE ANNEXURE) NABL)	5000.0
7.1&7.2,Table 1 (Chemical Analysis (Please see Annexure)- NON NABL)	1000.0

IS 2932 (2013) - Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
IS 2932 : 2013 (Please refer Annexure)	5000.0

IS:15778:2007 - CHLORINATED POLYVINYL CHLORIDE (CPVC) PIPES FOR POTABLE HOT AND COLD WATER DISTRIBUTION SUPPLIES

CHLORINATED POLYVINYL CHLORIDE (CPVC) PIPES FOR POTABLE HOT AND COLD WATER DISTRIBUTION SUPPLIES

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Mean Outside Diameter as per IS:15778:2007)	500.0
7.1.1 (Outside Dia. at any point as per IS:15778:2007)	500.0
7.1.1 (Max. Outside Dia. at any point as per IS:15778:2007)	500.0
7.1.1 (Min. Outside Dia. at any point as per IS:15778:2007)	500.0
7.1.2 (Average Wall Thickness as per IS:15778:2007)	1000.0
7.1.2 (Max. Wall Thickness as per IS:15778)	500.0
7.1.2 (Min. Wall Thickness as per IS:15778)	500.0
8 (Pipes Ends as per IS:15778)	1000.0
9.1 (Visual Appearance as per IS:15778)	1000.0
9.2 (Opacity as per IS:12235(Pt.-3))	1000.0
9.3 (Effect on Water as per IS:15778)	5000.0
9.4 (Reversion Test as per IS:12235(Part-5/sec.1))	1000.0
9.5 (Vicat softening Temperature as per IS:12235(Part-2))	1000.0
9.6 (Density as per IS:12235 (Part-14))	2000.0
10.1 (Hydrostatic Characteristics (Acceptance test) as per IS:12235(Part-8/sec.1))	5000.0
10.5 (Tensile Strength as per IS:12235(Part-13))	2000.0

Custom(Electrical)/01 - Custom(Electrical)

Custom(Electrical)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1.1 (Rain Fall Test)	15000.0

IRS TC 30-05 - IRS for Underground Railway Jelly Filled Telecom Quad Cables for Signalling & Telecom Installations

IRS for Underground Railway Jelly Filled Telecom Quad Cables for Signalling & Telecom Installations

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
5.2 (Type Test)	30000.0

IS 9862 (2017) - Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision)

Specification for ready mixed paint, brushing, bituminous, black, acid, alkali, water and chlorine resistlng (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3 table 1(v) (Mass, kg/10 Litres,)	1000.0

IS 2074 : 2023 (2023) - READY MIXED PAINT, AIR DRYING, RED OXIDE-ZINC CHROME PRIMING ― SPECIFICATION

READY MIXED PAINT, AIR DRYING, RED OXIDE-ZINC CHROME PRIMING ― SPECIFICATION

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Table 1 (Mass, in kg/10 l, (Part l/Sec 7))	500.0
Cl.5,7 Table 1 (Test Report-Please see Annexure)	20000.0

IS 133 (2013) - ENAMEL, INTERIOR : (A) UNDERCOATING (B) FINISHING

ENAMEL, INTERIOR : (A) UNDERCOATING (B) FINISHING

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Cl.5.1 Table 1 (TEST RESULTS (Please see the Annexure) AS PER CUSTOMER REQUEST)	4000.0
Cl.5.1 Table 1 (Test Results - (Please see Annexure) ALL PARAMETERS)	15000.0
Cl.5.1 Table 1 (TEST RESULTS-( PLEASE REFER ANNEXURE) UPTO 7 PARAMETERS)	5000.0

IS 15489 (2013) - Paint, plastic emulsion - Specification (First Revision)

Paint, plastic emulsion - Specification (First Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.5 (Mass in kg/10 litre (IS 101 (Part 1/Sec 7)))	500.0
6.11 (Finish)	1000.0
6.11 (Consistency (Annexure B of IS 15489:2013))	1200.0
6.11 (Drying time a) Hard dry (Class C and D) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Hard dry (Class A and B) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Surface dry (Class C and D) (Annexure D of IS 15489:2013))	200.0
6.11 (Drying time a) Surface dry (Class A and B) (Annexure D of IS 15489:2013))	200.0
6.9 (Lead Restriction)	1000.0
6.6 (Opacity (IS 101 ( Part 1/Sec 3)))	1000.0
6.4 (Application Properties)	700.0
6.3 (Thinning)	1200.0
6.11 (Colour (Annexure E of IS 15489:2013))	100.0
6.2 (Conditions in the Container)	200.0
6.11 (Gloss at 60 degree d) Class D)	200.0
6.11 (Gloss at 60 degree c) Class C, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree b) Class B, (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Gloss at 60 degree a) Class A (IS 101 (Part 4/Sec 4)))	200.0
6.11 (Recoating properties, (Annexure J of IS 15489:2013))	2000.0
6.12 (Volatile organic compounds,)	1500.0
6.12 (Toxic metals such as lead, cadmium, chromium (VI))	3600.0

12406 (2021) - Medium Density Fibre Board for General Purpose

Medium Density Fibre Board for General Purpose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
8.1 (Test for Dimensions (Length, Width and Thickness), in mm)	1000.0
8.2.1 (Test for Edge Straightness and Squareness, in mm/m)	500.0
9 (Test for Density, in kg/m^3)	1000.0
9 (Test for Density variation from Mean, %)	1000.0
9 (Test for Moisture Content and Variation from Mean)	1000.0
9 (Test for Linear Expansion (thickness swelling), due to general absorption after 24 hr, %)	1000.0
9 (Test for Internal Bond Strength, N/mm^2)	2000.0
9 (Test for Internal Bond Strength after Cyclic Test / Accelerated Water Resistance Test for Grade I Boards)	2000.0
9 (Test for Modulus of Rupture, N/mm^2)	2000.0
9 (Test for Modulus of Elasticity, in N/mm^2)	2000.0
9 (Test for Screw Withdrawal Strength, N)	1500.0
9 (Test for Formaldehyde Content, mg/100g)	2000.0
9 (Test for Steady State Formaldehyde Emission)	3000.0

IS/IEC 60168 (2000) - Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1000 V

Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1000 V

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
0 (Bending Test)	5000.0
0 (Compression Test)	5000.0

IS 7904 (2018) - High carbon steel wire rods - Specification (Second Revision)

High carbon steel wire rods - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7 (Carbon)	500.0
7 (Chromium)	500.0
7 (Sulphur)	500.0
7 (Manganese)	500.0
10 (Mechanical Properties (Tensile, Yield, Elongation & RA))	4000.0

IS:16647:2017 - Oriented Unplasticized Polyvinyl Chloride (PVC-O) Pipes for water Supply

Oriented Unplasticized Polyvinyl Chloride (PVC-O) Pipes for water Supply

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
7.1 (Visual Appreance, IS:16647)	1000.0
7.2 (Colour, IS:16647)	1000.0
5.5 (Density, IS:12235(part-14))	2000.0
7.3 (Opacity, IS:12235 (Part3))	1000.0
8.1.1.1 (Nominal Outside diameter, IS:16647)	1000.0
8.1.1.2 (Diameter at any point, IS:16647)	1000.0
8.1.2 (Wall Thickness, IS:16647)	1000.0
8.3 (Pipe Ends)	1000.0
9.1.1 (Resistance to Hydrostatic Pressure (Acceptance test), IS:16647)	5000.0
9.2 (Resistance to External Blows at 0 deg.C, IS:12235(Part-9))	2000.0
10 (Vicat softening Temperature, IS:12235(Part-2))	2000.0
10 (Resistance to Di-chloromethane at a specific temperature, IS:12235(Part-11))	2000.0
10 (Effect on Water, IS:12235 (Part-4&10))	5000.0

Custom specification CSD Canteen Electrical Lab samples - Custom specification CSD Canteen Electrical Lab samples

Custom specification CSD Canteen Electrical Lab samples

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
As per Annexure attached (Custom specification CSD Canteen Electrical Lab samples)	5000.0

Custom specification CSD Canteen Chemical Lab samples - Custom specification CSD Canteen Chemical Lab samples

Custom specification CSD Canteen Chemical Lab samples

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

NTH(WR)/MECH/CUSTOM/026 (2025) - Electric Traction Lifts-Component- Energy Accumulation Type Buffers

Electric Traction Lifts-Component- Energy Accumulation Type Buffers

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Load Rating test for car speed 0.76 to 1.0 m/s and stroke in 100mm as per IS 14665 part4 Section 1 Cl.5.1.2)	5000.0

303 (2024) - Plywood for General Purpose

Plywood for General Purpose

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
No Record Found

IS 13730(Part-9):1994,Reaffirmed 2005. (1994) - Specification for Particular Types of Winding Wires:Polyester Enamelled Round Aluminium Wire, Class 130

Specification for Particular Types of Winding Wires:Polyester Enamelled Round Aluminium Wire, Class 130

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4 (Dimensions)	1000.0
5 (Electrical Resistance)	2000.0
6 (Elongation)	1500.0
Tests (i)Measurement of diameter of conductor, ii)Measurement of increase in diameter,iii)Measurement of overall diameter,iv) Measurement of Elongation at break, v)Mandrel Winding Test,vi)Tensile Test on Conductor and vii)Weight check.)	10000.0

CSD-TDS Samples (2023-12) - CSD TDS ALL Index

CSD TDS ALL Index

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
63 (As per Annexure)	10000.0

IS 15931 (2012) - Solid Panel Foam UPVC Door Shutters - Specification

Solid Panel Foam UPVC Door Shutters - Specification

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
10.1 (Dimensions (Width, Height and thickness), in mm)	1000.0
10.1 (Squareness Test)	500.0
10.2 (General Flatness, in mm)	1000.0
10.3 (Impact Indentation Test,)	1000.0
10.4 (Edge Loading Test)	1500.0
10.5 (Shock Resistance Test [ Cl. 2.1 of IS 4020 (Part 8)])	1500.0
10.6 (Buckling Resistance Test, in mm)	1500.0
10.7 (Slamming Test,)	1000.0
10.8 (Misuse Test)	1000.0
10.9 (Screw Withdrawal Test,)	1000.0

IS 1664 (2002) - Mineral mixtures for supplementing cattle feeds - Specification (Fourth Revision)

Mineral mixtures for supplementing cattle feeds - Specification (Fourth Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
6.3 (Total ash in moisture free sample)	500.0
6.3 (Arsenic (as As2O3))	1000.0
6.3 (Lead (as Pb))	1000.0
6.3 (Acid Insoluble Ash)	500.0
6.3 (Sulphur)	1000.0
6.3 (Zinc (as Zn))	500.0
6.3 (Cobalt (as Co))	1000.0
6.3 (Manganese (as Mn))	500.0
6.3 (Copper (as Cu))	500.0
6.3 (Iodine (as KI))	1000.0
6.3 (Iron Content)	500.0
6.3 (Salt as NaCl)	500.0
6.3 (Magnesium)	500.0
6.3 (Phosphorus)	500.0
6.3 (Calcium (as Ca))	500.0
6.3 (Moisture)	500.0

IS 1964:2001 (2001) - Methods for Determination of Mass per Unit Lenght and Mass per Unit Area of Fabrics

Methods for Determination of Mass per Unit Lenght and Mass per Unit Area of Fabrics

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
Method-A (Grammage of Fabric (GSM))	1000.0

IS 10325 (2000) - Square tins - 15 kg/litre for ghee, vanaspati, edible oils and bakery shortenings - Specification (Second Revision)

Square tins - 15 kg/litre for ghee, vanaspati, edible oils and bakery shortenings - Specification (Second Revision)

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
4.3.1 (Body may be a single or two piece construction, soldered or welded as shown in Fig. 2A and Fig. 2B.)	1000.0

FSSAI - Food Safety and Standards (Contaminants, Toxins and Residues), Regulations, 2011

Food Safety and Standards (Contaminants, Toxins and Residues), Regulations, 2011

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Metal Contaminants)	5000.0

IS 2720 - Methods of Tests for Soils

Methods of Tests for Soils

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
- (pH)	1000.0

FSSAI (-) - Food Products Standard - Specifications for Oils and Fats [-]

Food Products Standard - Specifications for Oils and Fats

- View breakup
-

Clause No.	Testing Charges (Excl. Of Taxes)	NABL
1 (Test Result (As per Annexure))	5000.0

1
2
3
Next
Last